Lianxun Instruments S2011C Single-Channel PXIe Plug-in Source Measure Unit Precision Power/Measurement Unit ±60 V, ±3 A (DC), ±10 A (pulse)

Model：S2011C Country of Origin：China

Category：SMU Source Measure Unit

Overview：

A cost-effective single-channel PXIe source/measure unit that supports PXIe chassis from major vendors and multi-card synchronization. It can be integrated into production test systems to improve test throughput and reduce costs, and it supports Adaptive PFC.

Features

Specifications

Application Notes

Functions & Configuration

Features

High transfer rate
Single-channel standard PXIe precision power supply
High range
±60 V, ±3 A (DC), ±10 A (pulse)
High resolution
Minimum measurement resolution down to 100 fA / 100 nV
Easy to expand
Fits standard PXIe chassis for effortless multi-channel expansion

Features and benefits

5 functions in one
Voltage source
Current source
Ammeter
Voltmeter
Electronic load
Quadrants I and III operate as a source: the actual polarity of the V/I output follows the source setting;
Quadrants II and IV operate as a load: CC and CV work together; when used as a load, the load setting polarity is opposite to the source polarity;
Capable of testing a wide range of devices
Capture more measurement data
♦ 6.5-digit resolution: accuracy comparable to a 6.5-digit multimeter;
♦ 100 fA / 100 nV resolution: exceptional sensitivity for both sourcing and measurement;
♦ 1M points/s: high-speed measurement with fast setup and digitizing rates for arbitrary waveform generators and list sweeps;
Extensive sweep capabilities
DC I-V output capability
Pulsed I-V output capability

Voltage specifications

Voltage accuracy	Range	Setting resolution	Accuracy (1 year) ±(% reading + offset)1	Typical noise (RMS) 0.1 Hz-10 Hz
	±60 V2	10 μV	0.02%+3 mV	200 μV
	±6 V	1 μV	0.02%+0.3 mV	60 μV
	±0.6 V	100 nV	0.02%+50 μV	20 μV
Temperature coefficient	±(0.15 × accuracy specification)/°C (0℃-18℃, 28℃-50℃)
settling time	<50 μs (typical)
Overshoot	<±0.1% (typical, Normal, step is 10% to 90% of range, full-scale point, resistive load test)
Noise 10Hz-20MHz	6 V voltage source, 3 A resistive load, <5 mVrms

[1] Accuracy calculation example: to test the accuracy of a 120 mV output on the 600 mV range, the tolerance is:

[2] This instrument has potentially hazardous high voltage (±63 V) output to the HI/Sense HI/Guard terminals. To prevent electric shock, relevant safety precautions must be taken before powering on. Do not connect the Guard terminal to any output, including shorting it to chassis ground or output LO, otherwise the instrument will be damaged

Current specifications

Current accuracy	Range	Setting resolution	Accuracy (1 year) ±(% reading + offset)	Typical noise (RMS) 0.1 Hz-10 Hz
	±10 A3	1 μA	0.03% + 2mA	20 μA
	±3 A	1 μA	0.03% + 2mA	20 μA
	±1 A	100 nA	0.03% + 90 μA	3 μA
	±100 mA	10 nA	0.03% + 9 μA	200 nA
	±10 mA	1 nA	0.03% + 900 nA	20 nA
	±1 mA	100 pA	0.03% + 90 nA	2 nA
	±100 μA	10 pA	0.03% + 9 nA	200 pA
	±10 μA	1 pA	0.03% +1 nA	30 pA
	±1 μA4	100 fA	0.03% + 200 pA	5 pA
Temperature coefficient	±(0.15 × accuracy specification)/°C (0℃-18℃, 28℃-50℃)
settling time	<100 μs (typical)
Overshoot	<±0.1% (typical, Normal, step is 10% to 90% of range, full-scale point, resistive load test)

[3] The 10 A range supports pulse mode only; accuracy is typical

[4] For low-current measurement, triaxial cable connection is recommended: Hi to the center conductor, Guard to the inner shield, outer shield to protective ground; LO to the center conductor, inner shield unconnected, outer shield to protective ground. The rated insulation voltage of the coaxial cable shall be no less than 250 V

Minimum programmable pulse width	100 μs
Pulse width programming resolution	1 μs
Pulse width programming accuracy	±10 μs
Pulse width jitter	2 μs
Pulse width definition	As shown in the figure below, the time from the 10% leading edge to the 90% trailing edge

Pulse specifications	Maximum current limit	Maximum pulse width	Maximum duty cycle
1	0.4 A/50 V	DC, unlimited	100%
2	1 A/20 V	DC, unlimited	100%
3	3 A/6.6 V	DC, unlimited	100%
4	10 A/20 V	1 ms	5%
5	10 A/50 V	400 μs	2%

Looking for more sales, technical and solutions information?

Lianxun Instruments S2011C Single-Channel PXIe Plug-in Source Measure Unit Precision Power/Measurement Unit ±60 V, ±3 A (DC), ±10 A (pulse)

Leave a Message